UN 0012 1.4S Ammunition by Domestic Road, Rail, Air & Vessel (US Flag Carrier Only)

COMMODITY:             Small arms ammunition (shotshell, rimfire and centerfire) as 1.4S – 50 caliber / 8 gauge or less, inert bullets or tracer only; or above 50 Cal/8 gauge with an EX approval.

NOTE: Use LQ Data Sheets instead if package < 30 KG, primers are protected from other cartridges and ammo is in inner packages in an outer container. Use this data sheet for loose un-oriented “bulk” packs.

MODE OF TRANSPORTATION: Domestic Road – Less than truck load (LTL) and truck load (TL) service

—————————————————————————————————————-

OVERVIEW

PROPER SHIPPING NAME: Cartridges, small arms LABEL: None
IDENTIFICATION NUMBER: UN0012 PLACARD: None
HAZARD CLASS/DIVISION: 1.4S EMERG. INFO: Required
PACKING GROUP: None TRAINING: Required
DOCUMENT: Required PACKAGING: PI 130
MARKING: Required    

HAZARDOUS MATERIALS TABLE

(1)

Sym-
bols

(2)

Hazardous materials descriptions and proper shipping names

(3)

Hazard class or Division

(4)

Identifi-cation Numbers

(5)

PG

(6)

Label Codes

(7)

Special provisions

(§172.102)

(8)

Packaging (§173.***)

(9)

Quantity Limitations

(see §§173.27 and 175.75)

(10)

Vessel
stowage

Excep-tions

Non-
bulk

Bulk

Passenger aircraft/ rail

Cargo aircraft only

Loca-
tion

Other

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8A)

(8)

(8C)

(9A)

(9B)

(10A)

(10B)

Cartridges, small arms

1.4S

UN0012

none

63

62

None

25kg

100kg

01

25

CLASSIFICATION

Cartridges, small arms 50 cal or less with inert bullets (including tracers but no incendiary or exploding bullets) may be self-classified by the manufacturer as UN 0012, Cartridges, small arms, Division 1.4S explosive. No EX approval is required.

Citation: 49 CFR §173.56(h)

PACKAGING

Package the ammunition as follows:

  • Ammunition must be packed according to Packing Instruction 130. No inner package is required. This allows a loose un-oriented jumble pack in a box or drum.
  • The maximum gross weight is limited to 400 kg (882 pounds) per package.
  • A specification package is required, i.e. tested and certified with a mark, e.g.
    untitled-1

Citation: 49 CFR §173.62

SHIPPING PAPER REQUIREMENTS

1) Shipping description together and in order with no other information interspersed:

“UN 0012, Cartridges, small arms, 1.4S”.

2) The total quantity before or after the shipping description, in pounds and/or kilograms (lb or kg), covered by the shipping description in terms of net explosives mass, or the net mass, i.e. the weight of the powder and primer mix (primer mix may be negligible compared to powder) in the ammunition or the weight of the ammunition without any packaging. The degree of decimals or rounding is not specified, the recommendation is to use whole units, e.g. 5 lbs.

3) The number and type of packages, before or after the shipping description, e.g. “10 boxes” or “10 drums”. Commonly understood abbreviations may be used, e.g. “bx” or “drm”.

Option 1:

HM DESCRIPTION WEIGHT/LBS.
X UN0012 Cartridges, Small Arms, 1.4S
Net Explosive Mass = X,XXX KG (propellant weight, or optionally the net weight in the US only)
(Insert gross or net weight)

Option 2:

HM DESCRIPTION WEIGHT/LBS.
X UN0012 Cartridges, Small Arms, 1.4S
(Insert net or net explosives weight)

Citation: 49 CFR §172.202

________________________________________________________________________

PACKAGE MARKINGS

Packages containing small arms ammunition must display the following markings on one side as follows:

“UN 0012” ½” tall, or ¼” tall for 30 kg max, or an appropriate size for 5 kg max; “CARTRIDGES, SMALL ARMS”; the specification package marking.

A specification package certification mark, e.g.:

untitled-1

In addition, each carton may have to be marked with the consignor’s or the consignee’s name and address, see 49 CFR §172.301(d) for exceptions.

box-un0012

Citation: 49 CFR §172.300, 49 CFR §172.301(d)

________________________________________________________________________

OVERPACK MARKINGS

An overpack is:

  • a pallet
  • a spec packaging within a non-spec packaging, normally used for consolidation

The “Overpack” marking is required if at least one representative marking is not visible of the UN number, proper shipping name and the specification packaging marking for every hazardous material in the overpack. If any of these are not visible at least once in the overpack, all markings and labels should be reproduced on one side of the over, in addition to the “OVERPACK” mark.

The word “OVERPACK” may be a sticker, stenciled, or on a printed sheet of paper. It must be at least 0.5” tall as of 12/31/2016. It does not have to have a surrounding border.

Citation: 49 CFR §173.25

________________________________________________________________________